อีกทางเลือกประหยัดและคุณภาพสำหรับผู้ที่ใช้ตลับหมึกแยกสีของ HP ตลับใสเติมหมึกได้ HP ทำให้คุณประหยัดเงินลงไปได้หลายหมื่น และก็ไม่ต้องกลัวว่าสีจะที่ใช้จะไม่คุณภาพ จะไม่เหมื่อนของแท้
Set the paper in the rear tray, and press the OK button.
Paper jam.
[1300]
E03
Remove the jammed paper, and press the OK button.
Paper output tray open.
[1251]
E03
There may be an obstacle in front of the machine. Remove it, if any, and press the OK button.
Ink cartridge not installed, or not properly installed.
[1401]
E05
Install the ink cartridge properly. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge temperature sensor error.
[1403]
E05
Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Non-supported ink cartridge is installed.
[1485]
E05
A non-supported ink cartridge is installed. Install the supported ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge in a wrong position.
[1486]
E07
Install the ink cartridge in the correct position. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Multiple ink cartridges of the same color installed.
[1487]
E07
Confirm that each ink cartridge is installed in the correct position. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge hardware error
[1682]
E15
Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge not recognized.
[1684]
E14
A non-supported ink cartridge is installed. Install the supported ink cartridge.
The remaining ink amount unknown.
[1686]
E13
Replace the ink cartridge. Printing with an empty ink tank can damage the machine. To continue printing without replacing the ink cartridge, press the Stop/Reset button for 5 sec. or longer. (After the operation, it is recorded in the machine EEPROM that the function to detect the remaining ink amount was disabled.)
Ink cartridge not completely installed.
[1687]
E04
Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
No ink.
[1688]
E16
Replace the ink cartridge. Printing with an empty ink tank can damage the machine. To continue printing without replacing the ink cartridge, press the Stop/Reset button for 5 sec. or longer. (After the operation, it is recorded in the machine EEPROM that the function to detect the remaining ink amount was disabled.)
Warning: The ink absorber becomes almost full.
[1700]
E08
Replace the ink absorber, and reset the ink absorber counter. Pressing the Stop/Reset button will exit the error, and enable printing without replacing the ink absorber. However, when the ink absorber becomes full, no further printing can be performed unless the applicable ink absorber is replaced.
Service Call Error (Cyclic Blinking in Orange (Alarm LED) and Green (ON LED)
Cycles of blinking in orange and green
Error
Error code
7-seg. LCD
Conditions
Solution (Replacement of listed parts, which are likely to be faulty)
2 times
Carriage error
[5100]
P02
An error occurred in the carriage encoder signal.
1) Confirm that no foreign material is in the area where the carriage moves.
2) Clean the timing slit film. If it cannot be cleaned, replace it.
3) Replace the following items (listed in the order of likeliness to be faulty):
– Carriage unit
– Logic board
3 times
Line feed error
[6000]
P03
An error occurred in the LF encoder signal.
1) Perform the following for the timing slit disk film:
– Clean it.
– Re-attach it, if peeled off.
– Replace it, if it cannot be cleaned, or if it is deformed or damaged.
2) Replace the following items (listed in the order of likeliness to be faulty):
– Logic board
– Drive unit
5 times
ASF cam sensor error
[5700]
P05
This error takes place when feeding paper from the rear tray after an error occurred in the rear tray cam sensor.
1) Confirm that no foreign material is around the drive gear on the side of the drive unit.
2) Replace the following items (listed in the order of likeliness to be faulty):
– Drive unit
– Logic board
6 times
Internal temperature error
[5400]
P06
The internal temperature is not normal.
Replace the logic board.
7 times
Ink absorber full
Japan:
[5B00]
Others:
[5B01]
P07
The ink absorber becomes full.
Replace the ink absorber (ink absorber kit), and reset the ink absorber counter.
8 times
Print head temperature rise error
[5200]
P08
The print head temperature exceeded the specified value.
Replace the following items (listed in the order of likeliness to be faulty):
– Ink cartridge
– Logic board
9 times
EEPROM error
[6800]
[6801]
P09
A problem occurred in reading from or writing to the EEPROM.
Replace the logic board.
10 times
VH monitor error
[B200]
P10
The print head voltage is abnormal.
Replace the following items:
– Ink cartridge
– Logic board
20 times
Other hardware error
[6500]
P20
An unidentified error or a network error occurred.
Replace the following item (listed in the order of likeliness to be faulty):
– Logic board
– WLAN board
22 times
Scanner error
[5011]
P22
The scanner unit is faulty.
Replace the following items (listed in the order of likeliness to be faulty):
– Scanner unit
– Logic board
23 time
Scanner motor error
[5012]
P22
The scanner motor is faulty.
Replace the following items (listed in the order of likeliness to be faulty):
– Scanner unit
– Logic board
Other Error
7-segment LCD
Cause
Solution
E20
The wireless LAN setting was attempted while other settings were being performed.
Wait until the settings being performed were completed, then try the wireless LAN setting.
E23
In WPS wireless LAN setting, multiple access points were detected.
Wait for a while, and perform the setting again.
E24
In WPS wireless LAN setting, an error occurred.
Confirm the access point, and perform the setting again.
E50
The machine failed in scanning the print head alignment sheet.
Press the Stop/Reset button to clear the error, perform the following, then try the print head alignment again:
– Confirm that the sheet is placed in the correct orientation.
– Clean the platen glass, if it is smeared.
– Confirm that A4 plain paper is used.
– Print the nozzle check pattern to confirm that all the ink is ejected properly.
